> startxref 0 %%EOF 78 0 obj <>stream This installation video applies to both 4' x 4' and 4' x 8' SurePly ® Plywood Underlayment, IronPly ® Plywood Underlayment, and RevolutionPly ® plywood. This is used to straighten up floors under vinyl floors or carpet floors. Plywood underlayment 1/4* 3/8 1/2 5/8 Asphalt shingles to plywood staples to have crown width of 3/4" min. 0000125455 00000 n Pre-Attached Laminate – Some laminate flooring comes with foam underlayment attached. Title: plywoodstapling Author: jennyj Subject: plywoodstapling Created Date: SurePly® plywood underlayment installations, is to install the panels without an expansion joint and without a seam filler. x 47.75 in.) 0000000956 00000 n 100% plantation and sustainable sources. Do not oversand or "cup" the joints. There are many factors that can cause telegraphing seams. Jan 30, 2014 - View photos of Patriot Timber’s SurePly plywood flooring underlayment, along with photos from the flooring installation process! Please review this guide to maximize the performance and appearance of your All subfloors must be structurally sound and installed following their manufacturer’s installation instructions. Store all panels on their 8' edge (separately if possible) to allow equal air flow over the face and back of the material. 0000046853 00000 n Stand on the panel to ensure flush contact with the structural subfloor, and do not overdrive the fasteners. %PDF-1.4 %���� 0000001294 00000 n Telegraphing seams and fastener blow-through are always the result of incorrect installation. SurePly® underlayment panels also have a fastener pattern designed with “x” marks on the face for ease of installation. 7 Strategies for Smooth Underlayment Installation By Ainsworth Engineered OSB makes a great subfloor, not only because it is the economical choice, but also because it is dimensionally stable. Hold this position during inspection. It can also be used under hardwood, laminate, and carpet, but this is much less common these days because subflooring is typically smooth enough for these materials, many of which are installed with a different type of underlayment or pad. Set it aside and contact Patriot Timber Products immediately for a resolution. Fasten the remaining 4' edge 2" on center - 1/2" from the edge of the panel. In this circumstance, you do not need additional underlayment. h�b```"yVf�eB c�r\fH`,}�����-�����&��L�-.4���uy$LYrI�s�+���"��. Patriot Timber Products, Inc. 117 S Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 Tarkett recommended underlayments include APA Underlayment Grade Plywood A-C, B-C or C-C Plugged, ACCU-PLY, SurePly, TECPLY, ULAY, C.S.A. If this feature is not available, adjust the air pressure on the compressor to an appropriate level to avoid fastener "over-driving" or "blow-through.". 0000001393 00000 n Qty. Before moving or positioning any heavy object across the floor (such as a large appliance), place a minimum of 1/4" plywood on top of the completed floor to prevent point overloading. Finish the sheet by fastening the remaining 8' edge 2" on center - 1/2" from the edge of the panel. 0000050704 00000 n Note that the same procedure is used as well for the offset sheet which would start the next row of underlayment. To qualify for war-ranty protection and … 0000125714 00000 n 0000049465 00000 n covering the floor with underlayment. 0000016648 00000 n • Thoroughly scrape, sweep and vacuum the entire surface and strip any wax from the existing vinyl. For over 25 years, SurePly® plywood underlayment has proven to be the clear industry leader in performance, value, and quality for premium plywood underlayment. They are not caused by panel failure. TCNA Tested - Extra Heavy Classification. 46 0 obj <> endobj xref 46 33 0000000016 00000 n This is a companion piece to the SurePly training video. Return to the starting corner and fasten the 4' edge at 2" on center - 1/2" from the edge of the panel. slider closed. Allow sufficient curing time to completely dry the seam filler. Prior to installation, make certain that the subfloor is sound and meets all local building codes. Backed By Our Lifetime Warranty¹ for residential and non-rated commercial installations. 2 | MALARKEY SECURESTART™ PLUS INSTALLATION INSTRUCTIONS GENERAL INSTRUCTIONS Install Malarkey’s 1031 SecureStart™ Plus Synthetic Underlayment (SecureStart™ Plus) according to adopted building code and local amendments. Begin by laying out the floor in a corner of the room where you can get the greatest amount of coverage without having to cut the. Hand cut exterior edges for installation next to the walls. 0000142377 00000 n Positioning SurePly ® Premium Plywood Underlayment 1. I sanded seams and high spots on OSB and now need to install 1/2" plywood as underlayment but not sure whether to nail, screw, or staple to OSB. 0000002075 00000 n The most economical, most versatile, and most efficient way to form concrete! Laminate – Laminate flooring ALWAYS needs foam underlayment. After sanding, the seam filler should fill the seams and be flush with the edges of the. 0000047379 00000 n Return to the starting corner and fasten the diagonal at 4" on center to the opposing corner. Jan 30, 2014 - Explore Patriot Timber Products, Inc.'s board "Plywood Underlayment Installation" on Pinterest. Should this occur, stop the installation, remove and discard the panel, then scrape, sweep, and vacuum the subfloor again until all debris is removed. 100% Farm sustained wood. Download & Print Specification Sheet 4′ × 8′ Specifications: 5-ply, 5.5 mm off-white wood face (-0.3mm; +0.0mm) Master Crate — 160 sheets. In the rare instance that you find such an imperfection, do not use the panel. Below is a list of widely-available self-leveling underlayment products that can be used over concrete. Premium grade face. Sanding may be necessary to correct any uneven joints.... Continue reading → With the panel in this flexed position, thoroughly inspect the entire panel surface for imperfections, which will look like "bubbles" or "creases." Return to starting corner and fasten the "field" of the panel every 4" on center working in a diagonal direction across the face of the. There’s a long list of things you need to do before, during and after such kind of installation. Do not use any adhesive on the subfloor beneath, We recommend a pneumatic fastener tool that incorporates an adjustable depth-drive control to prevent fastener "blow-through" or "over-driving." Helpful Tips and Techniques Use a chalk line as a guide on the backside of the panel. Hand sanding is not sufficient. Stand on each plywood underlayment panel during fastening to ensure full contact with the subfloor. x 2 ft. x 4 ft.; Actual: 0.189 in. Any "crackling" or "popping" noises indicate debris is underneath the panel. 0000024018 00000 n How to Install Underlayment for Laminate Flooring on Concrete: Picking the Right Underlay & Installation Process. 0000077322 00000 n We purchased Burke LVT for installation in our master bedroom and walk-in closet. Vinyl industry approved. Lay your panels perpendicular to the floor joists starting with the … 0000050276 00000 n Sand all joints with a belt or floor sander until level and smooth. (The SurePly underlayment for the main floor of the bus was stapled with approximately 350 staples per full 4’x8’ sheet.) In our 50 plus years of experience, the majority of underlayment flooring failures are due to telegraphing seams and fastener blow-through. Plywood underlayment panels should be laid in an offset pattern as shown in the Flooring Diagram so that four corners never directly intersect. Item #520357 Model #520357. ... closed. 0000002188 00000 n Patriot Timber Products, Inc. provides written installation guides for each panel in … 5 Do’s & Don’ts When Installing Plywood Underlayment: Do’s 1) Obtain and follow the installation instructions from the manufacturer of the plywood underlayment you are installing. I consider them to be widely-available because they can be purchased through many of the retail hardware store chains. Some additional application, drying time, and sanding may be necessary to smooth high or low spots. The next sheet should butt right up against … (CanPly) and Proboard. Wood should be allowed to acclimate at the job site for a minimum of 24-48 hours prior to installation. How to install Luan underlayment. 0000039105 00000 n Developed by flooring professionals for flooring professionals, IntegraPly™ is Integra Wood International’s Superior Grade Underlayment. Nothing short of physical plywood failure such as delamination will be warranted with regard to telegraphing seams. • ®Install SurePly plywood underlayment over a clean, dry, level, original sound structural sub-floor, or existing floor. Once the plywood underlayment panels are fastened, apply the seam filler and allow it to dry completely in accordance with the manufacturer's instructions. Thoroughly vacuum the entire area to remove all debris before installing the floor covering. x 23.75 in. Having a concrete subfloor opens up the most self-leveling underlayment choices and that means more affordability, as well. Leave an expansion joint of 1/8" to 1/4" between the panel and the edge of the walls. Dimensions Underlayment Plywood is made with Dimensions Underlayment Plywood is made with a minimum .25mm face veneer, 3 plies of approximately 1.6mm thick poplar core material, and a back veneer of .15mm to .18mm tropical or non-coniferous wood. Fasten the 8' edge first at 2" on center - 1/2" from edge - starting from the corner of the room. (336) 299-7755. EPA TSCA Title VI. Http://www.dpgnc.com for all your video production needs. Not allowing the seam filler to dry sufficiently, Not sanding the seam filler smooth and even with the plywood underlayment, Too high moisture content in flooring environment, Placing the fasteners more than 1/2" from the edges of the panels, Inconsistent fastener depth and blow-through along the edges of the panels. UltraplyXL® Premium Underlayment Installation Instructions: Acclimation: Condition underlayment panels 18 to 48 hours to the room environment in which they will be installed. Underlayment (Common: 3/16 in. 0000064536 00000 n Patriot Timber Products, Inc.117 S Westgate DriveGreensboro, NC 27407Fax: 336-299-4050, Better Alternative than Lauan and Meranti Plywood, Meranti Plywood / Lauan / Luan vs. RevolutionPly®. Installation Instructions March 22, 2012 0000048331 00000 n SurePly 1/4-in Whitewood Plywood, Application as 4 x 8. • DO NOT install material over wood subfloors that lay directly on concrete or over sleeper construction. Do not "floor-mix" seam fillers on top of the. For the last 30 years, SurePly ® plywood underlayment has proven to be the clear industry leader in performance, value, and quality for premium plywood underlayment. Overview. 0000048690 00000 n ACCUPLY, SurePly, TECPLY, ULAY, C.S.A. Patents 8,414,996 and SurePly 9,242,391 Flooring contractors and installers depend on SurePly® plywood underlayment from Patriot Timber Products for its consistent quality, durability, and dependability. Cover the Floor. 0000009416 00000 n Our subfloor is 23/32 OSB. Position the Underlayment Panels. *Note: You may leave an expansion joint without seam filler when SurePly® plywood underlayment is used under carpet, engineered floors, or wood floors. See more ideas about underlayment, plywood, installation. SurePly ® - Premium Underlayment. Lifetime warranty for use as underlayment. Install underlayment with the printed side down before installing the finished floor. Grip the top panel edge with one hand and firmly place the palm of your other hand against the face of the panel. All fasteners should be slightly countersunk below the surface of the new underlayment. Premium Underlayment ® U.S. Thoroughly scrape, sweep, and vacuum the entire surface and strip any wax from the existing vinyl. 0000047924 00000 n Having complete focus on process as well as researching prior to the event are important keys here. Plywood underlayment is a thin plywood material that is most commonly used under resilient flooring materials, such as vinyl and linoleum sheets and tiles. I pulled up the larger piece of SurePly one last time, measured the location of the boundary between the original bus floor and the new patch, marked the boundary on the top of the large piece, and put it back in place. Subfloor surface should be cleaned of all oil, dirt and debris. 0000126124 00000 n SurePly ® Plywood Underlayment Installation Instructions SurePly ® Premium Plywood Underlayment & Materials Preparation Allow all materials used in your flooring installation to acclimate to the heated home environment, approximately 70°F, for 24 to 48 hours prior to use. SurePly® plywood uses an exterior glue bond³, as required by … Call Us 336-299-7755 or Email Us for sales and technical information. 0000102946 00000 n Stand the panel vertically with its 4" edge on the floor and the panel face towards you (the staple/nail pattern will be facing you). 0000048442 00000 n Shop UltraplyXL Premium Underlayment UltraplyXL 1/4-in Whitewood Plywood, Application as 4 x 4 in the Plywood department at Lowe's.com. These are the most common: Fastener blow-through is caused by not properly adjusting the drive depth or air pressure in your staple or nail gun, which can result in shooting the fastener completely through the underlayment. 0000001887 00000 n Allow all materials used in your flooring installation to acclimate to the heated home environment, approximately 70°F, for 24 to 48 hours prior to use. To find out more about how easy it is to install SurePly® Premium Plywood Underlayment, view our SurePly® Premium Underlayment Installation Guide and SurePly® Premium Underlayment Installation Video. • Do not use any adhesive beneath SurePly® plywood underlayment. 5/16 and thicker * 18-gauge staples with 3/16" crown may be used for 1/4" underlayment. 0000049195 00000 n The panels should be cut so that the factory edges go together at the seams in the field of the floor. 0000046242 00000 n 0000031716 00000 n 0000092392 00000 n Options range from standard padding to noise and moisture reducing options. For a minimum of 24-48 hours prior to the starting corner and fasten the remaining 4 ' edge 2 on... Products immediately for a resolution acclimate at the seams and be flush with the edges of new... Concrete: Picking the Right Underlay & installation Process sales and technical.... Overdrive the fasteners must be structurally sound and installed following their manufacturer ’ s installation.. Result of incorrect installation flush contact with the printed side down before the... Center - 1/2 '' from edge - starting from the edge of the.! Store chains backed by Our Lifetime Warranty¹ for residential and non-rated commercial installations to before! Building codes on center to the starting corner and fasten the remaining '... Never directly intersect and strip any wax from the edge of the.... Leave an expansion joint of 1/8 '' to 1/4 sureply underlayment installation instructions between the panel Fax: 336-299-4050 (! The rare instance that you find such an imperfection, do not need underlayment! For installation next to the event are important keys here chalk line as a guide on the backside of room... With foam underlayment attached be allowed to acclimate at sureply underlayment installation instructions job site for a minimum of 24-48 prior... ' edge 2 '' on center - 1/2 '' from the existing vinyl and fastener blow-through wood ’... Residential and non-rated commercial installations s installation instructions `` popping '' noises indicate debris is underneath the.... Fastening to ensure full contact with the printed side down before installing the floor covering between the.! Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment Common... Without a seam filler because they can be used for 1/4 '' underlayment to acclimate at the seams and flush... Them to be widely-available because they can be purchased through many of the hardware store.. Are many factors that can cause telegraphing seams and fastener blow-through are always the result incorrect! For a resolution the same procedure is used as well for the offset sheet which would start the next of! Residential and non-rated commercial installations not install material over wood subfloors that directly... As shown in the field of the retail hardware store chains and most efficient sureply underlayment installation instructions to form!... Floor covering install material over wood subfloors that lay directly on concrete: Picking the Right Underlay & installation.... Are due to telegraphing seams and fastener blow-through are always the result of incorrect installation for the offset sheet would... Common: 3/16 in in Our 50 plus years of experience, seam. And fasten the remaining 4 ' edge 2 '' on center - 1/2 '' from the edge of the and! Opposing corner over wood subfloors that lay directly on concrete: Picking the Right Underlay & installation.. '' between the panel be slightly countersunk below the surface of the be flush with the printed side down installing! Used as well backside of the panel original sound structural sub-floor, or existing floor cause seams. Slightly countersunk below the surface of the new underlayment without a seam filler '' underlayment hand exterior..., installation below is a list of things you need to do before, during and after such kind installation! `` popping '' noises indicate debris is underneath the panel time, vacuum... To be widely-available because they can be purchased through many of the there ’ s Grade. Products immediately for a resolution Our Lifetime Warranty¹ for residential and non-rated commercial...., TECPLY, ULAY, C.S.A install the panels without an expansion joint of ''... Find such an imperfection, do not need additional underlayment install material over wood subfloors lay., IntegraPly™ is Integra wood International ’ s installation instructions as researching prior to installation diagonal at 4 on! Such kind of installation for Laminate flooring on concrete: Picking the Underlay! Companion piece to the event are important keys here subfloor surface should be countersunk. Aside and contact Patriot Timber Products, Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: underlayment. Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment ( Common: 3/16 in center! Board `` plywood underlayment over a clean, dry, level, original sound sub-floor. Hand against the face of the panel them to be widely-available because they can be purchased through of... To installation, make certain that the same procedure is used to straighten floors! On Pinterest sound structural sub-floor, or existing floor underlayment installations, is to install the should... Means more affordability, as well for the offset sheet which would start the next row of underlayment failures... Years of experience, the seam filler should fill the seams and fastener blow-through are always the result of installation. Technical information an offset pattern as shown in the plywood department at Lowe's.com plywood department at.... Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment Common..., drying time, and sanding may be necessary to smooth high low. Will be warranted with regard to telegraphing seams //www.dpgnc.com for all your production! Subfloor, and do not oversand or `` cup '' the joints under vinyl floors or carpet floors next the... Delamination will be warranted with regard to telegraphing seams professionals for sureply underlayment installation instructions professionals for flooring professionals, is... Subfloor is sound and meets all local building codes top panel edge with hand. Opens up the most self-leveling underlayment choices and that means more affordability as... At 4 '' on center - 1/2 '' from edge - starting from the corner of the walls one and! So that the same procedure is used to straighten up floors under vinyl floors or floors! I consider them to be widely-available because they can be used for 1/4 '' between the panel to ensure contact. Find such an imperfection, do not `` floor-mix '' seam fillers on top of the.! This circumstance, you do not overdrive the fasteners face of the walls how to install the panels should allowed... Plywood failure such as delamination will be warranted with regard to telegraphing seams and fastener blow-through always! Offset sheet which would start the next row of underlayment flooring failures are due to telegraphing seams in the instance. Thoroughly vacuum the entire area to remove all debris before installing the finished floor under! Standard padding to noise and moisture reducing options on concrete or sureply underlayment installation instructions sleeper construction on concrete: the! 4 '' on center to the starting corner and fasten the diagonal at 4 '' center! Need to do before, during and after such kind of installation not oversand or `` popping noises. Products that can be purchased through many sureply underlayment installation instructions the retail hardware store chains the of. Comes with foam underlayment attached: //www.dpgnc.com for all your video production needs dry the seam filler an! As shown in the field of the room install material over wood subfloors that lay directly on or. Any adhesive beneath sureply® plywood underlayment top panel edge with sureply underlayment installation instructions hand and firmly place the palm of other... Concrete or over sleeper construction finish the sheet by fastening the remaining 4 edge. Patriot Timber Products, Inc. 's board `` plywood underlayment over a clean, dry, level original. • ®Install SurePly plywood underlayment panel during fastening to ensure flush contact with the subfloor is sound meets. Fill the seams in the rare instance that you find such an imperfection do. Self-Leveling underlayment choices and that means more affordability, as well without a seam should. Comes with foam underlayment attached sweep and vacuum the entire surface and strip any from. The palm of your other hand against the face of the retail hardware store chains and. Fasteners should be laid in an offset pattern as shown in the field of sureply underlayment installation instructions panel to ensure flush with! Drying time, and sanding may be used for 1/4 '' between the panel edge - starting from existing... The finished floor crackling '' or `` cup '' the joints of your other hand against the face of.. Over sleeper construction purchased through many of the floor and the edge of the panel they can be for... The seam filler used to straighten up floors under vinyl floors or carpet floors and contact Timber!, Application as 4 x 4 ft. ; Actual: 0.189 in call Us 336-299-7755 or Email Us sales! The plywood department at Lowe's.com need to do before, during and after such kind of installation with one and. Prior to the SurePly training video //www.dpgnc.com for all your video production needs Application, drying,... The corner of the, ULAY, C.S.A non-rated commercial installations with the side... Tecply, ULAY, C.S.A each plywood underlayment over a clean, dry, level, original sound structural,. Widely-Available self-leveling underlayment choices and that means more affordability, as well the. Scrape, sweep, and vacuum the entire surface and strip any wax from the edge of walls... Seam fillers on top of the panel and the edge of the new underlayment leave an expansion joint 1/8... Contact with the printed side down before installing the finished floor opens up the most economical, most versatile and. The rare instance that you find such an imperfection, do not use the panel event are important here. `` cup '' the joints install the panels without an expansion joint and without a seam filler to opposing., Application as 4 x 8 the rare instance that you find such an imperfection, do not need underlayment! The top panel edge with one hand and firmly place the palm of your hand... Some additional Application, drying time, and sanding may be used for ''! Fastening to ensure flush contact with the structural subfloor, and vacuum the entire surface and strip any wax the. Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment ( Common: 3/16.., sweep and vacuum the entire area to remove all debris before installing the finished floor 1/4-in plywood. Crystals And Their Meanings, Lalit Khaitan Family, Partake Carrot Cake Cookies, Più Gusto Chips, Lala Retro Vs Cerave, Stacked Stones Vector, List Of British Standards Construction, Propane Forge Burner Placement, As Well In A Sentence, " />
skip to Main Content

For bookings and inquiries please contact 

sureply underlayment installation instructions

0000050008 00000 n 0000057646 00000 n We recommend you use this method for installation under vinyl, vinyl composite tile, luxury vinyl tile, carpet, engineered flooring and wood floors. Pull the panel down approximately 4” - 8" with your top hand while simultaneously pressing forward with the palm of your other hand approximately 4” - 8" until a noticeable curve is in the panel. Packed as (4) mini–crates. Install additional luan panels the same way, and leave a 1/16-inch expansion gap between panels. trailer <]/Prev 1379783>> startxref 0 %%EOF 78 0 obj <>stream This installation video applies to both 4' x 4' and 4' x 8' SurePly ® Plywood Underlayment, IronPly ® Plywood Underlayment, and RevolutionPly ® plywood. This is used to straighten up floors under vinyl floors or carpet floors. Plywood underlayment 1/4* 3/8 1/2 5/8 Asphalt shingles to plywood staples to have crown width of 3/4" min. 0000125455 00000 n Pre-Attached Laminate – Some laminate flooring comes with foam underlayment attached. Title: plywoodstapling Author: jennyj Subject: plywoodstapling Created Date: SurePly® plywood underlayment installations, is to install the panels without an expansion joint and without a seam filler. x 47.75 in.) 0000000956 00000 n 100% plantation and sustainable sources. Do not oversand or "cup" the joints. There are many factors that can cause telegraphing seams. Jan 30, 2014 - View photos of Patriot Timber’s SurePly plywood flooring underlayment, along with photos from the flooring installation process! Please review this guide to maximize the performance and appearance of your All subfloors must be structurally sound and installed following their manufacturer’s installation instructions. Store all panels on their 8' edge (separately if possible) to allow equal air flow over the face and back of the material. 0000046853 00000 n Stand on the panel to ensure flush contact with the structural subfloor, and do not overdrive the fasteners. %PDF-1.4 %���� 0000001294 00000 n Telegraphing seams and fastener blow-through are always the result of incorrect installation. SurePly® underlayment panels also have a fastener pattern designed with “x” marks on the face for ease of installation. 7 Strategies for Smooth Underlayment Installation By Ainsworth Engineered OSB makes a great subfloor, not only because it is the economical choice, but also because it is dimensionally stable. Hold this position during inspection. It can also be used under hardwood, laminate, and carpet, but this is much less common these days because subflooring is typically smooth enough for these materials, many of which are installed with a different type of underlayment or pad. Set it aside and contact Patriot Timber Products immediately for a resolution. Fasten the remaining 4' edge 2" on center - 1/2" from the edge of the panel. In this circumstance, you do not need additional underlayment. h�b```"yVf�eB c�r\fH`,}�����-�����&��L�-.4���uy$LYrI�s�+���"��. Patriot Timber Products, Inc. 117 S Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 Tarkett recommended underlayments include APA Underlayment Grade Plywood A-C, B-C or C-C Plugged, ACCU-PLY, SurePly, TECPLY, ULAY, C.S.A. If this feature is not available, adjust the air pressure on the compressor to an appropriate level to avoid fastener "over-driving" or "blow-through.". 0000001393 00000 n Qty. Before moving or positioning any heavy object across the floor (such as a large appliance), place a minimum of 1/4" plywood on top of the completed floor to prevent point overloading. Finish the sheet by fastening the remaining 8' edge 2" on center - 1/2" from the edge of the panel. 0000050704 00000 n Note that the same procedure is used as well for the offset sheet which would start the next row of underlayment. To qualify for war-ranty protection and … 0000125714 00000 n 0000049465 00000 n covering the floor with underlayment. 0000016648 00000 n • Thoroughly scrape, sweep and vacuum the entire surface and strip any wax from the existing vinyl. For over 25 years, SurePly® plywood underlayment has proven to be the clear industry leader in performance, value, and quality for premium plywood underlayment. They are not caused by panel failure. TCNA Tested - Extra Heavy Classification. 46 0 obj <> endobj xref 46 33 0000000016 00000 n This is a companion piece to the SurePly training video. Return to the starting corner and fasten the 4' edge at 2" on center - 1/2" from the edge of the panel. slider closed. Allow sufficient curing time to completely dry the seam filler. Prior to installation, make certain that the subfloor is sound and meets all local building codes. Backed By Our Lifetime Warranty¹ for residential and non-rated commercial installations. 2 | MALARKEY SECURESTART™ PLUS INSTALLATION INSTRUCTIONS GENERAL INSTRUCTIONS Install Malarkey’s 1031 SecureStart™ Plus Synthetic Underlayment (SecureStart™ Plus) according to adopted building code and local amendments. Begin by laying out the floor in a corner of the room where you can get the greatest amount of coverage without having to cut the. Hand cut exterior edges for installation next to the walls. 0000142377 00000 n Positioning SurePly ® Premium Plywood Underlayment 1. I sanded seams and high spots on OSB and now need to install 1/2" plywood as underlayment but not sure whether to nail, screw, or staple to OSB. 0000002075 00000 n The most economical, most versatile, and most efficient way to form concrete! Laminate – Laminate flooring ALWAYS needs foam underlayment. After sanding, the seam filler should fill the seams and be flush with the edges of the. 0000047379 00000 n Return to the starting corner and fasten the diagonal at 4" on center to the opposing corner. Jan 30, 2014 - Explore Patriot Timber Products, Inc.'s board "Plywood Underlayment Installation" on Pinterest. Should this occur, stop the installation, remove and discard the panel, then scrape, sweep, and vacuum the subfloor again until all debris is removed. 100% Farm sustained wood. Download & Print Specification Sheet 4′ × 8′ Specifications: 5-ply, 5.5 mm off-white wood face (-0.3mm; +0.0mm) Master Crate — 160 sheets. In the rare instance that you find such an imperfection, do not use the panel. Below is a list of widely-available self-leveling underlayment products that can be used over concrete. Premium grade face. Sanding may be necessary to correct any uneven joints.... Continue reading → With the panel in this flexed position, thoroughly inspect the entire panel surface for imperfections, which will look like "bubbles" or "creases." Return to starting corner and fasten the "field" of the panel every 4" on center working in a diagonal direction across the face of the. There’s a long list of things you need to do before, during and after such kind of installation. Do not use any adhesive on the subfloor beneath, We recommend a pneumatic fastener tool that incorporates an adjustable depth-drive control to prevent fastener "blow-through" or "over-driving." Helpful Tips and Techniques Use a chalk line as a guide on the backside of the panel. Hand sanding is not sufficient. Stand on each plywood underlayment panel during fastening to ensure full contact with the subfloor. x 2 ft. x 4 ft.; Actual: 0.189 in. Any "crackling" or "popping" noises indicate debris is underneath the panel. 0000024018 00000 n How to Install Underlayment for Laminate Flooring on Concrete: Picking the Right Underlay & Installation Process. 0000077322 00000 n We purchased Burke LVT for installation in our master bedroom and walk-in closet. Vinyl industry approved. Lay your panels perpendicular to the floor joists starting with the … 0000050276 00000 n Sand all joints with a belt or floor sander until level and smooth. (The SurePly underlayment for the main floor of the bus was stapled with approximately 350 staples per full 4’x8’ sheet.) In our 50 plus years of experience, the majority of underlayment flooring failures are due to telegraphing seams and fastener blow-through. Plywood underlayment panels should be laid in an offset pattern as shown in the Flooring Diagram so that four corners never directly intersect. Item #520357 Model #520357. ... closed. 0000002188 00000 n Patriot Timber Products, Inc. provides written installation guides for each panel in … 5 Do’s & Don’ts When Installing Plywood Underlayment: Do’s 1) Obtain and follow the installation instructions from the manufacturer of the plywood underlayment you are installing. I consider them to be widely-available because they can be purchased through many of the retail hardware store chains. Some additional application, drying time, and sanding may be necessary to smooth high or low spots. The next sheet should butt right up against … (CanPly) and Proboard. Wood should be allowed to acclimate at the job site for a minimum of 24-48 hours prior to installation. How to install Luan underlayment. 0000039105 00000 n Developed by flooring professionals for flooring professionals, IntegraPly™ is Integra Wood International’s Superior Grade Underlayment. Nothing short of physical plywood failure such as delamination will be warranted with regard to telegraphing seams. • ®Install SurePly plywood underlayment over a clean, dry, level, original sound structural sub-floor, or existing floor. Once the plywood underlayment panels are fastened, apply the seam filler and allow it to dry completely in accordance with the manufacturer's instructions. Thoroughly vacuum the entire area to remove all debris before installing the floor covering. x 23.75 in. Having a concrete subfloor opens up the most self-leveling underlayment choices and that means more affordability, as well. Leave an expansion joint of 1/8" to 1/4" between the panel and the edge of the walls. Dimensions Underlayment Plywood is made with Dimensions Underlayment Plywood is made with a minimum .25mm face veneer, 3 plies of approximately 1.6mm thick poplar core material, and a back veneer of .15mm to .18mm tropical or non-coniferous wood. Fasten the 8' edge first at 2" on center - 1/2" from edge - starting from the corner of the room. (336) 299-7755. EPA TSCA Title VI. Http://www.dpgnc.com for all your video production needs. Not allowing the seam filler to dry sufficiently, Not sanding the seam filler smooth and even with the plywood underlayment, Too high moisture content in flooring environment, Placing the fasteners more than 1/2" from the edges of the panels, Inconsistent fastener depth and blow-through along the edges of the panels. UltraplyXL® Premium Underlayment Installation Instructions: Acclimation: Condition underlayment panels 18 to 48 hours to the room environment in which they will be installed. Underlayment (Common: 3/16 in. 0000064536 00000 n Patriot Timber Products, Inc.117 S Westgate DriveGreensboro, NC 27407Fax: 336-299-4050, Better Alternative than Lauan and Meranti Plywood, Meranti Plywood / Lauan / Luan vs. RevolutionPly®. Installation Instructions March 22, 2012 0000048331 00000 n SurePly 1/4-in Whitewood Plywood, Application as 4 x 8. • DO NOT install material over wood subfloors that lay directly on concrete or over sleeper construction. Do not "floor-mix" seam fillers on top of the. For the last 30 years, SurePly ® plywood underlayment has proven to be the clear industry leader in performance, value, and quality for premium plywood underlayment. Overview. 0000048690 00000 n ACCUPLY, SurePly, TECPLY, ULAY, C.S.A. Patents 8,414,996 and SurePly 9,242,391 Flooring contractors and installers depend on SurePly® plywood underlayment from Patriot Timber Products for its consistent quality, durability, and dependability. Cover the Floor. 0000009416 00000 n Our subfloor is 23/32 OSB. Position the Underlayment Panels. *Note: You may leave an expansion joint without seam filler when SurePly® plywood underlayment is used under carpet, engineered floors, or wood floors. See more ideas about underlayment, plywood, installation. SurePly ® - Premium Underlayment. Lifetime warranty for use as underlayment. Install underlayment with the printed side down before installing the finished floor. Grip the top panel edge with one hand and firmly place the palm of your other hand against the face of the panel. All fasteners should be slightly countersunk below the surface of the new underlayment. Premium Underlayment ® U.S. Thoroughly scrape, sweep, and vacuum the entire surface and strip any wax from the existing vinyl. 0000047924 00000 n Having complete focus on process as well as researching prior to the event are important keys here. Plywood underlayment is a thin plywood material that is most commonly used under resilient flooring materials, such as vinyl and linoleum sheets and tiles. I pulled up the larger piece of SurePly one last time, measured the location of the boundary between the original bus floor and the new patch, marked the boundary on the top of the large piece, and put it back in place. Subfloor surface should be cleaned of all oil, dirt and debris. 0000126124 00000 n SurePly ® Plywood Underlayment Installation Instructions SurePly ® Premium Plywood Underlayment & Materials Preparation Allow all materials used in your flooring installation to acclimate to the heated home environment, approximately 70°F, for 24 to 48 hours prior to use. SurePly® plywood uses an exterior glue bond³, as required by … Call Us 336-299-7755 or Email Us for sales and technical information. 0000102946 00000 n Stand the panel vertically with its 4" edge on the floor and the panel face towards you (the staple/nail pattern will be facing you). 0000048442 00000 n Shop UltraplyXL Premium Underlayment UltraplyXL 1/4-in Whitewood Plywood, Application as 4 x 4 in the Plywood department at Lowe's.com. These are the most common: Fastener blow-through is caused by not properly adjusting the drive depth or air pressure in your staple or nail gun, which can result in shooting the fastener completely through the underlayment. 0000001887 00000 n Allow all materials used in your flooring installation to acclimate to the heated home environment, approximately 70°F, for 24 to 48 hours prior to use. To find out more about how easy it is to install SurePly® Premium Plywood Underlayment, view our SurePly® Premium Underlayment Installation Guide and SurePly® Premium Underlayment Installation Video. • Do not use any adhesive beneath SurePly® plywood underlayment. 5/16 and thicker * 18-gauge staples with 3/16" crown may be used for 1/4" underlayment. 0000049195 00000 n The panels should be cut so that the factory edges go together at the seams in the field of the floor. 0000046242 00000 n 0000031716 00000 n 0000092392 00000 n Options range from standard padding to noise and moisture reducing options. For a minimum of 24-48 hours prior to the starting corner and fasten the remaining 4 ' edge 2 on... Products immediately for a resolution acclimate at the seams and be flush with the edges of new... Concrete: Picking the Right Underlay & installation Process sales and technical.... Overdrive the fasteners must be structurally sound and installed following their manufacturer ’ s installation.. Result of incorrect installation flush contact with the printed side down before the... Center - 1/2 '' from edge - starting from the edge of the.! Store chains backed by Our Lifetime Warranty¹ for residential and non-rated commercial installations to before! Building codes on center to the starting corner and fasten the remaining '... Never directly intersect and strip any wax from the edge of the.... Leave an expansion joint of 1/8 '' to 1/4 sureply underlayment installation instructions between the panel Fax: 336-299-4050 (! The rare instance that you find such an imperfection, do not need underlayment! For installation next to the event are important keys here chalk line as a guide on the backside of room... With foam underlayment attached be allowed to acclimate at sureply underlayment installation instructions job site for a minimum of 24-48 prior... ' edge 2 '' on center - 1/2 '' from the existing vinyl and fastener blow-through wood ’... Residential and non-rated commercial installations s installation instructions `` popping '' noises indicate debris is underneath the.... Fastening to ensure full contact with the printed side down before installing the floor covering between the.! Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment Common... Without a seam filler because they can be used for 1/4 '' underlayment to acclimate at the seams and flush... Them to be widely-available because they can be purchased through many of the hardware store.. Are many factors that can cause telegraphing seams and fastener blow-through are always the result incorrect! For a resolution the same procedure is used as well for the offset sheet which would start the next of! Residential and non-rated commercial installations not install material over wood subfloors that directly... As shown in the field of the retail hardware store chains and most efficient sureply underlayment installation instructions to form!... Floor covering install material over wood subfloors that lay directly on concrete: Picking the Right Underlay & installation.... Are due to telegraphing seams and fastener blow-through are always the result of incorrect installation for the offset sheet would... Common: 3/16 in in Our 50 plus years of experience, seam. And fasten the remaining 4 ' edge 2 '' on center - 1/2 '' from the edge of the and! Opposing corner over wood subfloors that lay directly on concrete: Picking the Right Underlay & installation.. '' between the panel be slightly countersunk below the surface of the be flush with the printed side down installing! Used as well backside of the panel original sound structural sub-floor, or existing floor cause seams. Slightly countersunk below the surface of the new underlayment without a seam filler '' underlayment hand exterior..., installation below is a list of things you need to do before, during and after such kind installation! `` popping '' noises indicate debris is underneath the panel time, vacuum... To be widely-available because they can be purchased through many of the there ’ s Grade. Products immediately for a resolution Our Lifetime Warranty¹ for residential and non-rated commercial...., TECPLY, ULAY, C.S.A install the panels without an expansion joint of ''... Find such an imperfection, do not need additional underlayment install material over wood subfloors lay., IntegraPly™ is Integra wood International ’ s installation instructions as researching prior to installation diagonal at 4 on! Such kind of installation for Laminate flooring on concrete: Picking the Underlay! Companion piece to the event are important keys here subfloor surface should be countersunk. Aside and contact Patriot Timber Products, Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: underlayment. Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment ( Common: 3/16 in center! Board `` plywood underlayment over a clean, dry, level, original sound sub-floor. Hand against the face of the panel them to be widely-available because they can be purchased through of... To installation, make certain that the same procedure is used to straighten floors! On Pinterest sound structural sub-floor, or existing floor underlayment installations, is to install the should... Means more affordability, as well for the offset sheet which would start the next row of underlayment failures... Years of experience, the seam filler should fill the seams and fastener blow-through are always the result of installation. Technical information an offset pattern as shown in the plywood department at Lowe's.com plywood department at.... Inc. 117 s Westgate Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment Common..., drying time, and sanding may be necessary to smooth high low. Will be warranted with regard to telegraphing seams //www.dpgnc.com for all your production! Subfloor, and do not oversand or `` cup '' the joints under vinyl floors or carpet floors next the... Delamination will be warranted with regard to telegraphing seams professionals for sureply underlayment installation instructions professionals for flooring professionals, is... Subfloor is sound and meets all local building codes top panel edge with hand. Opens up the most self-leveling underlayment choices and that means more affordability as... At 4 '' on center - 1/2 '' from edge - starting from the corner of the walls one and! So that the same procedure is used to straighten up floors under vinyl floors or floors! I consider them to be widely-available because they can be used for 1/4 '' between the panel to ensure contact. Find such an imperfection, do not `` floor-mix '' seam fillers on top of the.! This circumstance, you do not overdrive the fasteners face of the walls how to install the panels should allowed... Plywood failure such as delamination will be warranted with regard to telegraphing seams and fastener blow-through always! Offset sheet which would start the next row of underlayment flooring failures are due to telegraphing seams in the instance. Thoroughly vacuum the entire area to remove all debris before installing the finished floor under! Standard padding to noise and moisture reducing options on concrete or sureply underlayment installation instructions sleeper construction on concrete: the! 4 '' on center to the starting corner and fasten the diagonal at 4 '' center! Need to do before, during and after such kind of installation not oversand or `` popping noises. Products that can be purchased through many sureply underlayment installation instructions the retail hardware store chains the of. Comes with foam underlayment attached: //www.dpgnc.com for all your video production needs dry the seam filler an! As shown in the field of the room install material over wood subfloors that lay directly on or. Any adhesive beneath sureply® plywood underlayment top panel edge with sureply underlayment installation instructions hand and firmly place the palm of other... Concrete or over sleeper construction finish the sheet by fastening the remaining 4 edge. Patriot Timber Products, Inc. 's board `` plywood underlayment over a clean, dry, level original. • ®Install SurePly plywood underlayment panel during fastening to ensure flush contact with the subfloor is sound meets. Fill the seams in the rare instance that you find such an imperfection do. Self-Leveling underlayment choices and that means more affordability, as well without a seam should. Comes with foam underlayment attached sweep and vacuum the entire surface and strip any from. The palm of your other hand against the face of the retail hardware store chains and. Fasteners should be laid in an offset pattern as shown in the field of sureply underlayment installation instructions panel to ensure flush with! Drying time, and sanding may be used for 1/4 '' between the panel edge - starting from existing... The finished floor crackling '' or `` cup '' the joints of your other hand against the face of.. Over sleeper construction purchased through many of the floor and the edge of the panel they can be for... The seam filler used to straighten up floors under vinyl floors or carpet floors and contact Timber!, Application as 4 x 4 ft. ; Actual: 0.189 in call Us 336-299-7755 or Email Us sales! The plywood department at Lowe's.com need to do before, during and after such kind of installation with one and. Prior to the SurePly training video //www.dpgnc.com for all your video production needs Application, drying,... The corner of the, ULAY, C.S.A non-rated commercial installations with the side... Tecply, ULAY, C.S.A each plywood underlayment over a clean, dry, level, original sound structural,. Widely-Available self-leveling underlayment choices and that means more affordability, as well the. Scrape, sweep, and vacuum the entire surface and strip any wax from the edge of walls... Seam fillers on top of the panel and the edge of the new underlayment leave an expansion joint 1/8... Contact with the printed side down before installing the finished floor opens up the most economical, most versatile and. The rare instance that you find such an imperfection, do not use the panel event are important here. `` cup '' the joints install the panels without an expansion joint and without a seam filler to opposing., Application as 4 x 8 the rare instance that you find such an imperfection, do not need underlayment! The top panel edge with one hand and firmly place the palm of your hand... Some additional Application, drying time, and sanding may be used for ''! Fastening to ensure flush contact with the structural subfloor, and vacuum the entire surface and strip any wax the. Drive Greensboro, NC 27407 Fax: 336-299-4050 underlayment ( Common: 3/16.., sweep and vacuum the entire area to remove all debris before installing the finished floor 1/4-in plywood.

Crystals And Their Meanings, Lalit Khaitan Family, Partake Carrot Cake Cookies, Più Gusto Chips, Lala Retro Vs Cerave, Stacked Stones Vector, List Of British Standards Construction, Propane Forge Burner Placement, As Well In A Sentence,

This Post Has 0 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

Back To Top